molded choke coil ? pia1205sp series note: specifications subject to change without notice. please check our website for latest information. proprietary and confidential document of superworld 29/09/2017 p1 1. part no. expression: p i a 1 2 0 5 s p 1 r 0 m n a) series code e) tolerance code (a) (b) (c) (d) (e)(f) b) dimension code f) internal control code c) type code d) inductance code 2. configuration & dimensions: a. lead frame b. non lead frame 3. schematic: a b c d g h l e inductance 13.50.5 12.60.2 4.70.3 2.30.3 8.0 5.0 14.5 4.00.3 1.0uh and below 4.70.3 1.5uh and above note: 1. the above pcb layout is for reference only. 2. solder paste thickness of 0.15mm and above is recommended. 3. marking: top row ? inductance code, bottom row ? yyww l g h recommend pc board pattern unit: mm marking d/c marking d/c
molded choke coil ? pia1205sp series note: specifications subject to change without notice. please check our website for latest information. proprietary and confidential document of superworld 29/09/2017 p2 4. material list: i) lead frame ii ) non-lead frame a) core b) wire c) terminal d) ink 5. general specification: (a) operating temp. : -40c to +125c (inclusive of coil temp rise) (b) storage temp. : -40c to +125c (on board) (c) humidity range : 85 2% rh (d) heat rated current (irms) will cause the coil temperature rise approximately ? t of 40c (keep 1min) (e) saturation current (isat typ.) will cause l0 to drop approximately 30%. (f) part temp. (ambient + temp. rise) should not exceed 125c under worst case operating conditions. (g) storage condition (component in its packaging) i) temperature: -10 to 40c ii) humidity : 50~60% rh
molded choke coil ? pia1205sp series note: specifications subject to change without notice. please check our website for latest information. proprietary and confidential document of superworld 29/09/2017 p3 6. electrical characteristics: notes: 1) at all times, the current supplied to the product should not exceed isat max. value. 7. characteristics curves: part number inductance lo (uh) @ 0a 20% test frequency, l heat rating current dc ( a ) irms. saturation current dc (a) isat. dcr (m ? )typ. dcr (m ? )max. type typ. max. typ. max. pia1205spr47mn 0.47 100khz/1.0v 38 34 65 58 0.77 0.9 non lead frame PIA1205SPR68MN 0.68 100khz/1.0v 34 31 50 42 1.3 1.55 non lead frame pia1205sp1r0mn 1.00 100khz/1.0v 30 27 40 34 1.6 1.9 non lead frame pia1205sp1r5mn 1.50 100khz/1.0v 25 22 31 28 3.2 3.8 lead frame pia1205sp2r2mn 2.20 100khz/1.0 v 17 15.5 26 23 4.1 4.8 lead frame pia1205sp3r3mn 3.30 100khz/1.0 v 15.5 14 23 20.5 6.0 7.0 lead frame pia1205sp4r7mn 4.70 100khz/1.0v 14 12.5 18.5 16 8.8 10.2 lead frame pia1205sp6r8mn 6.80 100khz/1.0v 12 11 16.5 15 13 16 lead frame pia1205sp100mn 10.0 100khz/1.0v 10 9.0 13 10.5 19.2 22 lead frame pia1205spr47mn PIA1205SPR68MN pia1205sp1r0mn pia1205sp1r5mn pia1205sp2r2mn pia1205sp3r3mn
molded choke coil ? pia1205sp series note: specifications subject to change without notice. please check our website for latest information. proprietary and confidential document of superworld 29/09/2017 p4 8. soldering: mildly activated rosin fluxes are preferred. the minimum amount of solder can lead to damage from the stresses caused by the differenc e in coefficients of expansion between solder, chip and substrate. our terminations are suitable for all re-flow soldering systems. if hand soldering cannot be avoided, the preferred technique is t he utilization of hot air. 8-1 solder re-flow: recommended temperature profiles for re-flow soldering in figure 1. 8-2 soldering iron (figure 2): products attachment with soldering iron is discoura ged due to the inherent proc ess control limitations. in the event that a soldering iron must be employed the following precautions are recommended. note : a) preheat circuit and products to 150c. b) 355c tip temperature (max.) c) never contact the ceramic with the iron tip d) 1.0mm tip diameter (max.) e) use a 20 watt soldering iron with tip diameter of 1.0mm f) limit soldering time to 4~5 secs. pia1205sp4r7mn pia1205sp6r8mn pia1205sp100mn
molded choke coil ? pia1205sp series note: specifications subject to change without notice. please check our website for latest information. proprietary and confidential document of superworld 29/09/2017 p5 c d 2.00.5 embossed carrier b a cover tape 9. packaging information: 9-1 reel dimension: 9-2 tape dimension: 9-3 packaging quantity: type a(mm) b(mm) c(mm) d(mm) 13?x24mm 24.4+2/-0 1002 13.50.5 330 pia 1205 chip / reel 500 inner box 1000 carton 4000 series size bo(mm) ao(mm) ko(mm) p(mm) w(mm) f(mm) t(mm) d(mm) pia 1205 14.10.1 12.90.1 5 .50.1 16.00.1 24.00.3 11. 50.1 0.350.05 1.50.1
molded choke coil ? pia1205sp series note: specifications subject to change without notice. please check our website for latest information. proprietary and confidential document of superworld 29/09/2017 p6 9-4 tearing off force: application notice: 1. storage conditions: to maintain the solderabililty of terminal electrodes: a) recommended products should be used within 12 months from the time of delivery. b) the packaging material should be kept where no chlorine or sulfur exists in the air. 2. transportation: a) products should be handled with care to avoid damage or contamination from perspiration and skin oils. b) vacuum pick up is strongly recommended for individual components. c) bulk handling should ensure that abrasion and mechanical shock are minimized. room temp. ( ) room humidity (%) room atm (hpa) tearing speed mm/min 5~35 45~85 860~1060 300 the force for tearing off cover tape is 10 to 130 grams in the arrow direction under the following conditions.
|
